DIO-1616RYN-ETH

Device Name Setting/Network Setting

Fail-Safe Setting

Firmware Update


Device Name Setting/Network Setting

1. After LAN connecting your PC and this device, start the CONTEC Device Utility.

2. When this device is newly detected, "(New) DIO-1616RYN-ETH" will be displayed in the "NET" tree, and the temporary device name is displayed in the light yellow "Device Name".

3. Set the following "Setting item" and click the "Save" button.
   The target device will automatically reboot and the settings will be applied.
   The setting itself has been completed so far.

4. The configured device is indicated as "[device name] DIO-1616RYN-ETH", and the device name is displayed in the white "Device Name".

5. If you select this configured device, the "Diagnosis" button will be enabled.
   Clicking this button will start Diagnostic program and check the operation.
   Please refer "Home > Digital I/O Driver > Utility > Diagnosis Program" to know more details.

6. If you want to change the setting contents, please click "Save" again after changing.

 

[Device information area] Display information of the selected device

Device Type

Display device type

Device

Display product model

MAC Address

Display MAC address

Group ID

Display group ID setting value

 

[Setting item] You can set the selected device

Device Name

Set the device name.

It cannot have the same name as any other device.

When specifying a device from an application, specify this device name.

Unit ID

Set unit ID.*1

When using this product multiple units, it is necessary to set the unit ID uniquely.

  Settable range: 0 to 127  (Rotary switch settable range is 0 to 7)

IP Address

Set IP address.*2

Subnetmask

Set the subnet mask.*2

Default Gateway

Set the default gateway.*2
When setting is unnecessary, set 0.0.0.0.

Port Open

Specifies to use event notification or sampling function notification.
If unchecked, the event notification or sampling function of the ETH device will not be available.

When checked, the port on the PC side will be released and connections from the ETH device UDP 0X501F will be allowed.
Also, an inbound rule is added in the firewall settings.

CONTEC [DIOxxx(Device Name) DIO-XXX-ETH(Device)]

After confirming that the device's event notifications are working properly,
please change the Windows OS firewall settings as necessary to adjust the security level to meet the system requirements.

*1 When the Group ID is 8, the unit ID depends on the setting of the unit rotary switch and cannot be changed by the utility.
  If Group ID is A, set the unit ID here.

*2 Please make appropriate settings for these settings according to your network environment.

 


Fail-Safe Setting

1. After LAN connecting your PC and this device, start the CONTEC Device Utility.

2. Set the following "Setting item" on the "FailSafe" tab.
   To output multiple data with fail-safe, check "Output Multi Data" and make settings on the "FailSafe(MultiData)" tab as well.

3. Click the "Save" button.
   The target device will automatically reboot and the settings will be applied.

 

See also "FailSafe Setting" for details on the fail-safe function.

 

[Setting item] You can set the selected device

"FailSafe" tab

Event Trigger

- Linkdown

Select this when activating fail-safe when link down state occurs, such as when the LAN cable is disconnected.

Event Trigger

- No Access

Select this when activating fail-safe when there is no access for the set time.

  Settable range: 1 to 600 (*100msec)

Start wait time

Set the time to disable the fail-safe function after turning on the power.

The fail-safe function is enabled after the set time has elapsed.

  Settable range: 0 to 3600 (sec)

FailSafe OutBit (Hex)

Set the output terminal to output with the fail-safe function.

Set the output terminal in hexadecimal.

  Settable range: 0000 to 000F

  Setting example: To use output terminals 0, 1, 2, 3, set 000F

Output Data (Hex)

Set the output data to be output with the fail-safe function.

Set 0 or 1 output in hexadecimal from the output terminal set with "FailSafe OutBit (Hex)".

  Settable range: 0000 to 000F

  Setting example: To set the output of output terminals 0, 1, 2, 3 to "0, 1, 0, 1", set 000A

Output Multi Data

Check this if you want to output multiple data continuously when fail-safe is activated.

When checked, the "FailSafe(MultiData)" tab will appear, so set up multiple data there.

FailSafe status

You can check the fail-safe activation state and reset the output when activated.

This button is enabled by setting the Device Name.

 

"FailSafe(MultiData)" tab

Output Data (Hex) 1-8

Up to eight fail-safe output data can be set.

The setting method is the same as above "Output Data (Hex)".

Hold Time (*100msec) 1-8

Set the data output time in units of 100 milliseconds.

After this time, the next data is output.

  Settable range: 1 to 600 (*100msec)

patterns

Set the number of data to be output.

Repeat

After outputting the number of data set with "patterns", set whether to repeat output from 1 of "Output Data" again.

If you do not repeat, select "1 time".

To repeat infinitely, select "Infinite".

It can also be repeated a certain number of times, the setting range is 2 to 255 times.

 


Firmware Update

1. Turn off the power of this device and set the Group ID to "E".

2. After LAN connecting your PC and this device, start the CONTEC Device Utility.

3. When this device is detected with Group ID "E", "DIO-ETH-TYPE2" is displayed in the "Setting mode" tree.

4. When selecting a device, "Current version" shows the current firmware version.

5. When clicking "Write new firmware", a file selection dialog is displayed.
   Please select the firmware file to be written.

   After writing, the target device automatically restarts and the new firmware will be applied.
   Firmware update itself has been completed so far.

6. Re-launching the utility will redetect the device.
   Please confirm that the version of "Current version" has been updated.

 

* For DIO-1616RYN-ETH, when setting Group ID to "E", the IP address of this device will be fixed at "192.168.0.1", so consider this when using it through a router.
* When updating more than one device, please operate one by one.